Last updated November 17, 2026
New windows and doors improve comfort, cut energy bills and add long-term value to your home. Sightline Windows & Doors Summerlin pairs proven product lines with a local vetted installing partner for lasting performance - and a price put in writing.
Choose your installer
The unit is half the job - the install is the other half. Background-checked local installers measure, set, seal and insulate every opening, and they know the lines we quote inside and out.
Select the right products
Compare styles, materials and glass packages side by side until the fit is right for your rooms, your budget and your goals. The product-line comparison below is the place to start.
Prepare your home for install
Before install day we walk you through a short checklist - furniture pulled back, treatments down, a clear path to each opening - so install day is watch-it-happen, not scramble.
Compare the Lines We Quote
Every project is priced on the same lines, side by side - the price indicators below are relative, and your consultant shows exact numbers on your actual openings.
PGTThe line homeowners arrive naming - the most impact certifications in the industry$$$
- More impact certifications than any other line we quote
- WinGuard, EnergyVue and ClassicVue Max systems built for every wind zone
- 99% on-time delivery keeps your install date on the calendar
CGIThe heavyweight impact line$$$$$
- Large-missile impact ratings for the strictest wind zones
- Architectural-grade aluminum with commercial-depth frames
- The line we quote when protection is the whole point
CWSThe value pick$$
- Vinyl systems built to strict wind codes
- Strong energy packages at the friendliest price point
- The smart start for whole-home replacements on a budget
ESWSlim lines, big glass$$$$
- Narrow-sightline aluminum for modern elevations
- Oversized openings and floor-to-ceiling glass
- Impact-rated without the bunker look
ECOThe aluminum impact workhorse$$$
- Factory-built aluminum impact systems
- A strong price-to-protection ratio for coastal homes
- Proven lines with short lead times
Impact Windows & Doors Troubleshooting: Common Problems and How to Fix Them
A crack in a standard insulating glass unit means the glass is done. A crack in laminated impact glass can leave the unit intact, held together by its interlayer, while the structural integrity of the system is already compromised in ways you cannot see. Those are two different problems, and they demand two different responses. Most troubleshooting advice treats every window the same, which is why so many Summerlin homeowners get the wrong diagnosis and pay for the wrong fix. This guide covers the failure patterns specific to laminated glass and impact-rated frames: crack assessment, interlayer delamination, multi-point door hardware, condensation behavior, and how to route a warranty claim to the right party.
Quick Answer

Impact windows and doors fail differently than standard glass units, so troubleshooting starts with identifying which component failed: the laminated glass, the frame and weatherseal, or the hardware. A cracked impact pane that still holds together is not automatically safe, edge clouding usually points to a seal or interlayer problem rather than a glass defect, and a door that won’t latch is almost always a hardware alignment issue rather than a failed lock body. Document the failure with photos and frame readings before calling anyone, because that record determines both the fix and the warranty path.
Before
AfterTable of Contents
- How to Assess a Cracked Impact Window
- Interlayer Delamination: Clouding and Yellowing at the Edges
- Impact Door Hardware: Diagnosing Multi-Point Lock Failures
- Condensation on Impact Glass in Summerlin’s Swing Season
- Which Warranty Covers the Failure?
- The Annual Owner Check We Recommend
- Common Mistakes to Avoid
- When to Call a Professional
How to Assess a Cracked Impact Window

Laminated impact glass is built from two panes bonded to a plastic interlayer, and that interlayer is the reason a broken unit can stay in its frame. That is a real safety feature. It is also the reason a cracked impact window gets misread as “still fine.”
When we inspect a damaged impact unit in Summerlin, we work through the same sequence every time:
- Locate the crack relative to the interlayer. A hairline in the outer lite with no spidering and no displacement may be cosmetic in the short term. A crack that runs to the edge of the glass is a different matter, because edge cracks concentrate stress at the frame and can propagate.
- Press gently near the break. If you feel movement, hear crackling, or see the two lites separate slightly, the interlayer has lost its bond. The unit is no longer performing its impact function regardless of how it looks.
- Check for fogging between the lites. Moisture inside the sealed assembly means the perimeter seal is gone, which usually means the unit needs replacement.
- Look at the frame. Displaced glass often means the frame deflected on impact. A glass-only replacement into a bent frame will not restore the rated assembly.
The honest answer is that any crack in an impact-rated unit should be evaluated by someone who can read the frame and the seal, not just the glass. Call (844) 560-5201 and we will tell you what we see in the photo record before anyone orders product. If you want the background on how these systems are specified in the first place, our page on window installation in Summerlin walks through the assembly layer by layer.
Interlayer Delamination: Clouding and Yellowing at the Edges
Delamination is the interlayer separating from the glass, and in Summerlin it shows up first at the edges. The signature is a milky haze creeping inward from the frame line, sometimes with a yellow or amber tint in older units. It is easy to confuse with condensation, so start there: condensation sits on the surface or between panes as droplets and clears with weather. Delamination is inside the laminate, does not clear, and does not move.
Summerlin sits at roughly 3,000 feet with intense UV load and summer surface temperatures that push west- and south-facing glass hard. That combination accelerates any weakness at the edge seal. The causes fall into two buckets:
- Product or manufacturing: incomplete edge seal, moisture trapped during lamination, or an interlayer that was not compatible with the assembly. This is a glass manufacturer’s warranty matter.
- Installation or glazing error: a unit set with inadequate edge clearance, a blocked weep path, or glazing that pinches the glass so it cannot move with thermal expansion. That stress shows up at the edges first, and it is an installation issue, not a glass defect.
That distinction matters because it decides who pays. A delaminated unit with clean edge clearance and intact weep channels points to the glass. A delaminated unit sitting tight against a shimmed frame with clogged drainage points to how it was set. We see both in Summerlin, and we photograph the edge detail on every visit so the answer is documented rather than argued. If your units are past the point of repair, our window replacement in Summerlin page covers what a measured replacement looks like and how the written price is built.
Impact Door Hardware: Diagnosing Multi-Point Lock Failures

Impact-rated doors carry heavier slabs and stiffer frames than standard doors, which is why most of them use a multi-point lock: one handle operates several locking points up and down the edge, engaging keeps set into the frame. When a multi-point system stops working, the symptom is almost always “the door won’t lock,” but there are three distinct causes and they need three different fixes.
1. A misaligned keep. The door latches at the handle but one of the upper or lower points won’t engage. Look at the strike area for a bright rub mark or a scratch on the keep. The frame has shifted slightly, usually from settlement or thermal movement. The fix is realigning or re-shimming the keep, not replacing the lock.
2. A failed actuator. The handle turns but nothing moves, or it moves at one point and not the others. That is an internal gear or linkage failure in the lock body. The door will feel normal until you test every point individually.
3. A sagging slab. The door drags at the bottom corner, the handle is stiff, and the lock engages only if you lift the door while turning. That is a hinge or anchor problem, and forcing the lock will damage it further. Impact slabs are heavy enough that a slightly loose top hinge translates into visible sag within a season.
Test it in this order: open the door, operate the handle and watch whether every point extends fully; close it lightly and check for rub marks at each keep; then lift the handle to see whether the geometry changes. That sequence tells you which of the three problems you have. For a full look at how these doors are specified and set, see our door installation in Summerlin page.
Condensation on Impact Glass in Summerlin’s Swing Season
Impact glass behaves differently from standard double-pane glass in one respect that confuses a lot of homeowners: the laminated layer adds a third material to the assembly, and the thermal bridge at the edge is often more pronounced. In Summerlin’s swing months, when nights drop into the 40s and afternoons climb past 75, it is normal to see condensation on the outside surface in the morning or on the interior during a cold snap. Surface condensation that clears as the day warms is thermal behavior, not a failure.
What is not normal:
- Moisture between the panes. Fog or droplets inside the sealed cavity mean the seal has failed. No amount of weather change will clear it.
- Persistent wetness at the bottom of the glass inside the frame. Usually a blocked weep channel or a sill that was set without proper drainage slope. Water sitting at the edge is what drives delamination, so this one matters.
- Condensation that appears only on one unit and not its neighbors. Isolated behavior points to a specific seal or installation fault, not climate.
Summerlin also has interior humidity differences that matter: a home with a whole-house humidifier set high will fog impact glass that a drier house never touches. Before assuming a seal failure, check the indoor relative humidity and whether the pattern tracks the weather or stays put. We’ve seen plenty of “failed seals” in Summerlin turn out to be a humidifier set at 45 percent in January.
Which Warranty Covers the Failure? Glass, Frame, or Installation

This is where most homeowners lose time. An impact window is a system, and the warranty is split across three parties who each want different evidence. Route the claim to the wrong one and you will get a denial that has nothing to do with whether the failure is real.
- Glass manufacturer’s warranty covers the sealed unit: seal failure, fogging between lites, delamination traced to lamination. Most require the unit’s serial or identification label, the manufacture date, and photos of the defect including the edge.
- Frame manufacturer’s warranty covers the frame, sash, and integral hardware. A bent frame, a failed weld, or a multi-point lock body that failed internally belongs here. They typically want photos of the frame extrusion and the lock mechanism, plus the model number stamped on the frame.
- Installation warranty covers how the system was set: shimming, drainage, flashing, anchoring, and operation. A unit that leaks at the perimeter, a door that sags because the anchor pattern was wrong, or a keep that was never aligned falls here. The evidence is the installation record.
This is the argument for a documented photo record on every job. Under the Haven Standard, every visit leaves one, because when a claim comes up years later the photos of how the opening was set are the difference between a covered repair and a dispute. Sightline installs across eight manufacturer lines including CGI, CWS, and ES Windows, and we specify by what the opening requires, which means the warranty documents stay with the customer rather than disappearing into a file. If a failure is unclear, call (844) 560-5201 and we will help identify which party owns it.
The Annual Owner Check We Recommend
Most impact failures we see in Summerlin give early signals a year or more before they become visible problems. Fifteen minutes twice a year, before summer and after, catches them:
- Walk every unit and look at the edges. Clouding, yellowing, or a bright line where the interlayer meets the glass.
- Open and close every impact door and operate every locking point. Feel for stiffness at the handle and check that all points engage.
- Look for rub marks at the keeps. A scratch on the strike metal tells you the geometry has moved.
- Check the weep channels and sill drainage. Debris from a windy spring blocks them fast.
- Photograph anything new. Date the photos. A two-year history of an edge haze is far stronger evidence for a warranty claim than a memory.
Do this before the summer heat peaks, not after. Summerlin’s UV loads degrade a compromised edge seal faster than a mild climate ever would.
Common Mistakes to Avoid

- Assuming a cracked impact unit is safe because it holds together. The interlayer keeps glass in the opening; it does not restore the assembly’s rated performance.
- Treating edge clouding as condensation. In Summerlin, that mistake usually costs a homeowner a season of the warranty window.
- Forcing a multi-point lock that won’t engage. Forcing a stiff handle bends the actuator and turns a keep alignment into a lock replacement.
- Calling the glass manufacturer about a leak. Perimeter leaks are installation, and the frame manufacturer will refer you right back. Diagnose first.
- Grinding or re-aligning a keep without addressing the hinge. If the door is sagging, the keep will drift again within a season.
- Caulking over a drained sill. Plugging the weep path traps water at the glass edge, which is exactly what causes delamination in our climate.
- Replacing one unit of a set without checking the frame. In Summerlin, a displaced frame from a wind event typically affects the units around it too, and the frame reading tells you.
When to Call a Professional
Call in a professional for any crack that reaches the glass edge, any moisture between the lites, delamination spreading more than a quarter inch from the frame, a door that will not latch at every point, or a unit whose frame has moved. Also call before you cut, drill, or re-caulk anything on a laminated unit: the interlayer is unforgiving of a poorly sealed cut and the repair will cost more than the original inspection. If a cracked lite is within reach, tape it on both sides as a temporary measure but do not press or flex the glass. Sightline Windows & Doors Summerlin offers free estimates in Summerlin, with a written price before any work starts and a free second opinion on any written estimate from a competitor. Call (844) 560-5201.
Frequently Asked Questions

A crack that runs to the glass edge, any movement you can feel when pressing near the break, or fogging between the lites means the unit needs replacement. A small chip away from the edge may be assessed as cosmetic, but only an inspection of the frame and seal confirms it. Call (844) 560-5201 and we will review photos before anyone recommends product.
It can be either, and the difference is in the edge detail. Clean edge clearance with intact weep channels points to a glass or interlayer defect covered by the manufacturer; a unit pinched tight against the frame with blocked drainage points to installation. Document it and get it assessed early.
Usually one of three things: a misaligned keep, a failed actuator inside the lock body, or a sagging slab. Test each locking point separately with the door open to see which one fails to extend. Call (844) 560-5201 for an assessment before forcing the handle.
Surface condensation that clears as the day warms is normal thermal behavior, especially during our swing months. Moisture between the panes is not normal and signals a failed seal. Persistent wetness at the bottom inside the frame points to a drainage problem worth inspecting.
An assessment is free with us, and the written price for any repair is provided before work starts. Replacement pricing depends on the unit size and the frame condition, which is why we measure before quoting rather than giving a number over the phone. Call (844) 560-5201 for an exact quote – estimates are free.
We install across eight lines including CGI, CWS, ES Windows, and ECO Window Systems, specified by what the opening requires rather than what is in stock. That range matters for troubleshooting because the warranty path depends on which manufacturer built the unit.
The Bottom Line
Impact windows and doors fail differently from standard units, and the diagnosis has to start with which part failed: glass, frame, hardware, or installation. A crack needs a frame and seal check before you assume it is fine. Edge clouding is either a product defect or a setting error, and the edge detail tells you which. A door that won’t lock is a geometry problem first, a lock problem second. Condensation that clears is thermal; condensation that stays is a seal. And every one of these comes down to documentation, which is why the written record matters as much as the repair itself. For a full look at how we approach the whole home, see Sightline Windows & Doors Summerlin home.
Call Sightline Windows & Doors Summerlin at (844) 560-5201 for a free estimate. Every job starts with a measured survey you keep, a written price before any work begins, and a documented photo record when it is done.
Written by the team at Sightline Windows & Doors Summerlin.
Six Reasons Homeowners Choose Sightline Windows & Doors Summerlin

Laminated glass and reinforced frames hold up to wind-driven rain, hail and flying debris, so your openings stay sealed when the weather turns.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Tighter seals and insulated glass even out hot and cold rooms and stop the drafts at the frame.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.
Other Sightline Windows & Doors Summerlin Services
What Neighbors Say About Sightline Windows & Doors Summerlin
